Search results

BOD B94CGU 120-277 VAC, 50 /60 HZ, ONE-LAMP ILLUMINATION FOR 4-PIN LAMPS,EMERGENCY BALLAST

10 Watt Emergency Driver for Linear LED Strips, 120-277 Volt, 90 Minute Illumination Time, Metal Case No Conduit

Category: LED Driver Emergency Power Supplies

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277V, 90 Minute Illumination Time, 24 Hr Recharge. For use with the following 350-450 Lumen Compact, Linear & U-Bent Fluorescent Lamp Types: (1) 17-40W, 2-4 ft T8, T10, T12 or 4-Pin Long Compact

Category: Emergency Fluorescent Ballasts

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277V, 90 Minute Illumination Time, 24 Hr Recharge. For use with the following Lamp Types: (1) Philips LED T8 InstantFit, BiPin, 8.5 - 16.5W. (designated by new Silver Can)

Category: Emergency Fluorescent Ballasts

LED Emergency Driver. Input Voltage: 120/277 Volts AC, 60Hz. Output Voltage: 120/277 VAC, 60Hz. Maximum Load Power (including AC ballast/driver): 100 Watts. SINE WAVE Emergency Lighting inverter with Dimming Capabilities

Category: LED Driver Emergency Power Supplies

LED Emergency Driver - Input Voltage: 120-277V AC. Operates an LED Load of up to 10W at nominal battery voltage for a minimum of 90 minutes. UL RECOGNIZED Factory Installation * (Indoor and Damp) Output Class 2 Compliant **BSL310 is field installable when used with the Philips EvoKit LED Retrofit Luminaire and installed by Licensed Electrician** See pg. 6 of Wiring Diagram .pdf **

Category: LED Driver Emergency Power Supplies

Lighting Relay Control Device, 20 Amp, 120/277 Volt

Category: Emergency Lighting Backup Battery Accessories

EMERGENCY DRIVER FOR LED STRIPS CLASS 2 OUTPUT 10 WATTS OUTPUT POWER

BOD BSL310C EMERGENCY LED DRIVE 10W OUTPUT

BOD BSL20 HV Emergency LED Driver, 0.16A-0.10A, 125V-200V

Category: LED Driver Emergency Power Supplies

LED Emergency Driver - Input Voltage: 120-277V AC. Matal Case with Conduit. Operates an LED Load of up to 10W at nominal battery voltage for a minimum of 90 minutes. Listed to UL924 and tested to CSA 22.2, No. 141 For Field or Factory Installation (Indoor and Damp) Output Class 2 Compliant **BSL310 is field installable when used with the Philips EvoKit LED Retrofit Luminaire and installed by Licensed Electrician** See pg. 6 of Wiring Diagram .pdf **

Category: LED Driver Emergency Power Supplies

10 Watt Emergency Driver for Linear LED Strips, 120-277 Volt, 90 Minute Illumination Time

Category: LED Driver Emergency Power Supplies

10 Watt Emergency LED Driver, Class 2 Output, Very Compact Low Profile Case, ABConnect and STSelect Equipped, Metal IP65 Bi-Color LED and Test Switch, 14.1” x 1.18” x 1"

Category: LED Driver Emergency Power Supplies

LED Emergency Driver, 6 Watt, 120-277 Volt Input, 15-54 Volt DC Output

Category: LED Driver Emergency Power Supplies

Emergency Lighting Kit: 1000+ lumens (with Supplied Module); Provides Emergency Lighting From the Internal Battery Upon Loss of AC Power. For Use With Most Luminaire Types and Independent of the Luminaire Components. Driver: 14.1" H x 1.18" W x 1.0" D (358mm x 30mm x 25mm), Mounting Center 13.78" (350mm). LED Module: 5.0" H x 1.0" W (127mm x 25mm), Mounting Center 2.65" (67.4mm). IP65 Plenum Rated Bi-Color Illuminated Test Switch with 36" leads. 12 NC number: 913702492501

Category: Emergency Lighting Backup Battery Packs

(2) Wire Bundle Covers. For use with Emergency Ballast. ***May be required by State Law***

Category: Emergency Fluorescent Ballast Mounting Covers