Heat Pumps & Accessories

Used to support the 6x4 and 4x4 systems by spanning two threaded rod drops. Can be installed from above or below. Bracket is secured to each threaded rod with two nuts. The pre-assembled slide clamp enables fast assembly to channel. Use 7/16in nut driver

Category: Brackets

Used to support the 12x4 system, dual 6x4, or dual 4x4 systems attaching to the top of cabinets. Adjustable from 4 1/4" (108mm) to 12" (305mm) allowing runs to be leveled over uneven cabinet heights. Bracket is secured to the cabinet frame with through bo

Category: Brackets

Used to support the 6x4 and 4x4 systems from existing threaded rod installations. Bracket is secured to threaded rod with two split nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver on slide clamps, For 5/8" Thread

Category: Brackets

Used to support the 12x4 system from any new threaded rod extending down directly from the ceiling, grid, or ladder rack system. Two position height adjustments to accommodate system with or without hinged cover. Bracket is secured to threaded rod with tw

Category: Brackets

Used to support the 6x4 and 4x4 systems from any new threaded rod extending down directly from the ceiling, grid, or ladder rack system. Two position height adjustments to accommodate system with or without hinged cover. Bracket is secured to threaded rod

Category: Brackets

Used to support the 6x4 and 4x4 systems attaching to the top of an equipment rack. Contains hardware to mount to the top of EIA/TIA equipment racks. No threaded rod required. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut dr

Category: Brackets

Used to support the 6x4 and 4x4 systems from any new threaded rod installations. Bracket is secured to threaded rod with two nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver on slide clamps, For 16mm Threaded Rod.

Category: Brackets

Used to support the 6x4 and 4x4 systems from below with new threaded rod. Bracket is secured to threaded rod with two nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16in nut driver on slide clamps. Also can be secured directly

Category: Brackets

Used to support the 12x4 system by spanning two threaded rod drops that are 18in apart. Can be installed from above or below. Bracket is secured to each threaded rod with two nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16in

Category: Brackets

Used to support the 6x4 and 4x4 systems attaching to the top of cabinets. Adjustable from 4 1/4" (108mm) to 9" (229mm) allowing runs to be leveled over uneven cabinet heights. Bracket is secured to the cabinet frame with through bolts (not included). The

Category: Brackets

Wall Mounted Heat Pump, Unit Only, Indoor, High CFM: 390/425, 230/208V, Up To 9,000 BTU Rated, Energy Stat Rated, Includes: Wireless Remote Controller. ***Requires EPA Section 608 certification for installation

Category: Indoor Units - Wall Mount

SpeediChannel 90° Elbow, Long, Size: 4", Paintable, Color: Natural, Includes: Stainless Steel Screws.

Category: Line Hide Channel Elbows

24K BTU 16.0 SEER SINGLE ZONE WALL MOUNTED COOLING & HEATING OUTDOOR UNIT

Category: Outdoor Units

SpeediChannel Clip With 11" Cable Ties, Slides Into Place On A Railing Molded To The Inside Of The SpeediChannel, Pack of 10 Clips

Category: Line Hide Channel Clips & Brackets

4 Inch SpeediChannel Flat Wall Escutcheon, Used To Cover A Rough Opening In A Soffit, Wall, Or Ceiling Penetration, Snaps Onto The SpeediChannel, Paintable, Color: Natural

Category: Line Hide Channel Connectors & Adaptors

Wall Mounted Heat Pump, Indoor Unit, High CFM: 433, 208/230V, 24.6 SEER, 12,000 BTU, Includes: Wireless Remote Controller, Max Lineset Length Without Adding Refrigerant: 25'. ***Requires EPA Section 608 certification for installation

Category: Indoor Units - Wall Mount